Showing results: 31 - 38 of 38 items found.
-
Data Patterns Pvt. Ltd.
Data Patterns' core business for over 20 years has been the development of Automated Test Equipment for critical aerospace requirements. Data Patterns developed a Multi Programmer with associated test automation software in 1994. Christened the DP-800 this product was adopted for the implementation of test rigs for Navigation Platform Test Benches, Engine Test Bed Automation, Cable Harness Test Systems, etc. This product was effectively utilized in the development of test benches required by Indian Space Research Organisation (ISRO) for the Polar Satellite Launch Vechicle (PSLV) and Geo Stationary Launch Vehicle (GSLV). Based on this foundation, the next generation test benches were developed in the cPCI architecture. Presently, Data Patterns develops cPCI based test systems for Laboratory applications as well as VME based test systems for challenging environmental conditions. Examples of test solutions built by Data Patterns are indicated below.
-
SMX-7XXX (Microwave) -
AMETEK VTI Instruments
The AMETEK VTI Instruments SMX-7000 Series of microwave switch cards extends functionality typically reserved for dedicated stand-alone systems into the PXIe from-factor. Single and dual slot configurations provide the ability to mix and match multiple switch configurations including SPDT, SP4T, SP6T and Transfer. Embedded virtual schematic control further simplifies setup and debugging allowing all relays to be engaged independent of application software and device drivers. Ideally suited for medium-to-high density automated test equipment (ATE), the SMX-7000 Series deliver uncompromised measurement integrity ideal for the most demanding aerospace, defense and communication applications.
-
ATE -
Frontier Electronic Systems Corp.
The design, development, manufacture and integration of Automated Test Equipment (ATE) systems is a core technology focus for FES. Our engineers have designed and manufactured complex flight line test systems for military aircraft such as the F-15, F-18, C-17, B-1, B-52 and OV-22 aircraft. In 1994, FES developed the Common Core Test Set to test space systems electronics for the Defense Support Program (DSP). This open-architecture, high-reliability electronics test set has been upgraded over the last 20 years with new hardware and graphics-based software to accommodate the complex testing requirements associated with the International Space Station Rotary Joint Motor Controller and other satellite electronics. Maritime ATE systems designed and manufactured by FES include Radar & Video Distribution factory test systems supporting US and Canadian Navy customer production requirements. Core components of FES-developed ATE systems include the use of PXI/PCI/VXI/VME technologies, National Instruments Test Stand software, Agilent Technologies instrumentation, and Virginia Panel interface hardware. The FES ATE design team employs CMMI level 3 compliant processes throughout the design process from Systems Requirements Analysis through verification and validation of ATE compliance with customer hardware, software, and documentation requirements.
-
N6705C -
Keysight Technologies
The N6705C DC Power Analyzer provides unrivaled productivity gains for sourcing and measuring DC voltage and current into the DUT by integrating up to 4 advanced power supplies with DMM, Scope, Arb, and Data Logger features. The N6705C eliminates the need to gather multiple pieces of equipment and create complex test setups including transducers (such as current probes and shunts) to measure current into your DUT. The DC Power Analyzer also eliminates the need to develop and debug programs to control a collection of instruments and take useful measurements because all functions and measurements are available at the front panel. For even greater control and analysis functions, the DC Power Analyzer can be used with the 14585A Control and Analysis Software. When automated bench setups are required, the N6705C is fully programmable over GPIB, USB, LAN and is LXI Compliant. 14585A Control and Analysis Software
-
Granite River Labs Inc.
PCI Express® 4.0 Receiver Test Automation Software Suite (GRL-PCIE4-RXA) provides an automated, simple and efficient way to test your 4.0 designs using the Anritsu MP1900A with any Tektronix and Keysight Real-Time Oscilloscope oscilloscope. The GRL-PCIE4-RXA Test Suite features two components that can be ordered separately or bundled together. GRL-PCIE4-BASE-RXA is used for testing your PCIe® 4.0 Receiver to the Base (ASIC) Specification, while GRL-PCIE4-CEM-RXA is used for testing end products to the PCIe® 4.0 CEM (Card Electro-Mechanical) Specification. GRL-PCIE4-RXA provides a simple user interface to automate complex PCIe testing. The software runs on Windows 7 or higher oscilloscope or any PC OS, and significantly reduces equipment calibration and test time. For Base Specification testing, GRL software uses the industry-standard Seasim statistical data eye simulator to establish the calibrated test channel DDJ. The final calibrated eye diagram uses both Seasim and SigTest software to arrive at the final stressed eye diagram. Receiver jitter tolerance and margin testing can then be performed on the device under test. For CEM Spec testing, GRL software uses VNA method for Channel measurement and SigTest for all other stressed eye impairments. Jitter Tolerance and Margin Testing is offered in both BASE and CEM software versions of the software, while The CEM version provides all the tests required by the PCIe® 4.0 CEM CTS. Transmitter testing is also available using GRL-PCIE34-TXP1 Software and Controller. If ordered with with GRL-PCIE4-RXA Receiver test software, all PCIe® 4.0 CTS CEM tests (Transmitter and Receiver) can be performed on the MP1900 and any vendor’s Real-Time Oscilloscope using GRL’s automation framework without the need for vendor specific software tools.
-
PAT-2E -
Sonel S.A.
The innovative combination of small dimensions (full portability of the device) with advanced measuring systems allow to carry out fully automated measurements for electrical equipment, IEC cables and extension cords (including those with PRCD). The set of tests is performed with one click of START button. Confi guration options of the meter allow you to modify the operation of the device, and thus, tailor it to the needs of the user. In situations, where it is necessary to perform simple and single measurement, without the need to do complex measurement procedure, Pat Sonel allow you to work in a single measurement mode of a given type (ie. Manual). All meters in this series (PAT) also allow you to make basic measurements without external power in emergency situations i.e. in the absence of the power one can easily run a simplifi ed set of test in a battery mode. Small size, weight, and specially designed carrying case of the meter and accessories provide comfort and high mobility. Wireless communication with a printer enables organization of the working site without the hassle of unnecessary cables. Storage and integration of the results in PC software further extends the functionality of the instrument.
-
PAT-10 -
Sonel S.A.
The innovative combination of small dimensions (full portability of the device) with advanced measuring systems allow to carry out fully automated measurements for electrical equipment, IEC cables and extension cords (including those with PRCD). The set of tests is performed with one click of START button. Configuration options of the meter allow you to modify the operation of the device, and thus, tailor it to the needs of the user. In situations, where it is necessary to perform simple and single measurement, without the need to do complex measurement procedure, Pat Sonel allow you to work in a single measurement mode of a given type (ie. Manual). All meters in this series (Pat) also allow you to make basic measurements without external power in emergency situations i.e. in the absence of the power one can easily run a simplified set of test in a battery mode. Small size, weight, and specially designed carrying case of the meter and accessories provide comfort and high mobility. Wireless communication with a printer enables organization of the working site without the hassle of unnecessary cables. Storage and integration of the results in PC software further extends the functionality of the instrument.
-
PAT-2 -
Sonel S.A.
The innovative combination of small dimensions (full portability of the device) with advanced measuring systems allow to carry out fully automated measurements for electrical equipment, IEC cables and extension cords (including those with PRCD). The set of tests is performed with one click of START button. Confi guration options of the meter allow you to modify the operation of the device, and thus, tailor it to the needs of the user. In situations, where it is necessary to perform simple and single measurement, without the need to do complex measurement procedure, Pat Sonel allow you to work in a single measurement mode of a given type (ie. Manual). All meters in this series (PAT) also allow you to make basic measurements without external power in emergency situations i.e. in the absence of the power one can easily run a simplifi ed set of test in a battery mode. Small size, weight, and specially designed carrying case of the meter and accessories provide comfort and high mobility. Wireless communication with a printer enables organization of the working site without the hassle of unnecessary cables. Storage and integration of the results in PC software further extends the functionality of the instrument.
